sublimation printing

Since printer ink bonds to paper fibers, it is harder to remove  it. Today, we will share 2 methods to solve this problem. 1. T ake a cotton ball and dab the fresh ink. Most printers spray ink droplets. This will continue to be wet for a couple of minutes. It is possible to pick up the ink if you act swiftly after the paper gets printed. If this is done, the next step becomes considerably much easier. Whatever you do, you must not rub the paper in a vigorous manner. Doing this may rip the paper. Cheaper inks are easier to remove than their pricier counterparts. The second step is to gently scrape paper with a razor blade or sandpaper. This is most successful if the ink remains on the paper surface. Scrape the paper's top level off by using ultra fine sandpaper or razor blade. Scraping should be done in only one direction. This is towards yourself. Chances of success are increased if the paper is thicker. If the ink is UV cured, it can be scraped off much easily. If the ab...

1. Inkjet printer print blank fault check The first thing to check the allowance is that the surplus is enough to cause the printing blank. Most of the failures are due to nozzle blockage, ink cartridges and so on. 2.Troubleshooting of inkjet printer output blackening 1) Troubleshoot: There may be two reasons: ink cartridge, printer not used for a long time or direct sunlight, resulting in nozzle blockage. 2) Solution: You can change the cartridge or inject ink. If the cartridge is not used up, it can be concluded that the nozzle is blocked: remove the cartridge (for cartridge nozzles). The integral printer needs to remove the nozzle. Soak the nozzle in warm water for a while. Be careful not to immerse the circuit board in the water, otherwise it will be used. The result is unthinkable. The operation is recommended under the guidance of factory engineers. 3. New ink cartridges do not print out of water after loading, showing the ink 1) Do not remove the labe...

Digital printing  is becoming more and more mature and is eroding the traditional screen printing market. Nowadays, the development of digital printing has drawn people a beautiful blueprint for getting rich. However, due to the equipment and processing procedures required for professional digital printing are very tedious, the printing effect is also unsatisfactory, personalized digital printing has been unable to find an entry point. As a result, many people are not familiar with digital printing and want to use flatbed printers to print pigments or even dye inks to obtain qualified printed products. However, if they do not perform professional textile processing, it is difficult to obtain satisfactory results. This is mainly due to that fabrics only can be used after pretreating and post-processing. The digital printing technology that is often overlooked and most mature is indeed sublimation transfer digital printing. It is th...

Sublimation transfer printing technology has developed rapidly in our country and has a wide range of applications.  Today,we will introduce t he principle and characteristics of  it for you. The principle The sublimation transfer printing first uses the printing method to print a special printing dye onto a transfer paper, and then heats and presses the dye onto the fabric. Specifically, it is based on the sublimation characteristics of disperse dyes, select the sublimation temperature range of 180 ~ 240 °C disperse dyes . Then mix it with the slurry color ink . A ccording to the different patterns, pattern requirements, with Ep ~ J ,t he ink is printed on the transfer paper . A nd the transfer paper printed with patterns and patterns is brought into close contact with the fabric, processed on a transfer printing machine at 200-230° C   for 10-30 s . A nd the dye is transferred from the printing paper to the fabric. After diffusion into the fabric to achieve the...

In the process of digital printing,we may meet this situation- Print head nozzle disconnection. Do you know the cause of print head nozzle disconnection and how to deal with this problem?Today,we will analyze it for you. The cause of print head nozzle disconnection 1. Physical damage due to collisions, paper jams, folds, etc. This situation can only replace the new nozzle. 2. Because the machine is idle for a long period of time, the nozzle's residual ink causes the nozzle to clog. In this case, the nozzle needs to be soaked with cleaning liquid, requiring professional maintenance personnel to operate it. 3. Environmental factors. The working environment requires suitable temperature and humidity, temperature between 18-25 degrees, and humidity around 50. If the temperature is too low or the humidity is too low, the nozzle will be short-term. The specific reason is not explained in detail. 4. Continuous printing, large area and large background color printing...

I once read a sentence and deeply agree that "Any product in the world is irreplaceable".Of course, print head is the irreplaceable small product. The user's operating method and basic maintenance in use  are also important factors that affect the long-term use of printer's print head. "illegal" operation We should try to avoid the following situations: 1. Bad habits in daily work. 2 . A sudden power failure during printing caused the print head not to return to normal position. 3 . One-sided pursuit of speed during the printing process pulls paper. 4 . Open the front cover during printing and do harm to the print head, such as pulling paper, wiping parts, etc. 5 . Try to change the position of the parts when the power is on. For example, forcibly pull the carriage from the maintenance cartridge. 6 . For convenience, move the device while the printer is working. Empty print head In daily work, due to long hours, a lot of work, o...

It's important for laser cutting equipment operators to know the rules of laser beam focusing.Do you know three focal points relations of laser cutting machine ?Now,let ’ s make a brief introduction for you. 1. Cutting focus on the workpiece In this way we also become a negative focal length, because the cutting point is not located on the surface of the cutting material nor is it located inside the cutting material, but is located above the cutting material. This method is mainly used with cutting materials with high thickness. The reason why the focus of this approach is on the cutting material is mainly due to the need for thicker cuts of the thick plate, otherwise the oxygen delivered by the nozzle is extremely prone to cause insufficient and the cutting temperature is reduced. However, one of the disadvantages of this approach is that the cutting surface is rough and not very practical for high-precision cutting. 2 .  C utting focus inside the workpiece This me...